We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

ARB Air Locker Installation Manual: Step-by-Step Guide (2026)

Using an arb air locker installation manual? This guide walks through the install steps, tools, air line routing and testing so your locker engages reliably on

Updated November 2026

An arb air locker installation manual is the official reference for mounting an ARB air locker into a differential, routing the air line, wiring the solenoid and confirming the locker engages correctly. This guide explains how those manuals are typically organized, what you need on the bench before you start, and the order of operations that most installers follow. Use it alongside the manual for your specific axle, not in place of it.

Read the Manual Before You Touch a Wrench

Most ARB installation manuals assume you already know the basics of differential service. Before you start, confirm the manual matches your axle housing (for example, Dana 30, Dana 44 or Toyota 8-inch) and the locker model in the box. Check the parts list against what you received, and note the torque specifications, which are the values you will refer to most often. The manual will also list whether the ring gear and carrier need to be removed, which determines how much of the differential you must disassemble.

Shopping for one? See our guide: ARB Air Locker Differential Review (2026).

Prepare the Differential and Mount the Locker

Drain the gear oil, remove the cover and pull the carrier assembly. Clean the carrier thoroughly and inspect the ring gear, pinion and bearings for wear before continuing. Many manuals call for replacing the carrier bearings and seals during the job, since access is already open. Install the air locker body into the carrier following the manual’s sequence, and set the preload and backlash to the stated values using the shims or adjusters provided.

Common preload and backlash checks

  • Set bearing preload to the range in the manual using a torque wrench on the carrier bearing caps.
  • Measure ring gear backlash with a dial indicator and adjust within the specified window.
  • Verify gear contact pattern with marking compound before reassembly.

Route the Air Line and Wire the Solenoid

The air line runs from the locker’s inlet fitting to the solenoid valve, then to your compressor or air tank. Route it away from exhaust heat, moving suspension parts and sharp edges, and secure it with the clips included in the kit. Follow the manual’s wiring diagram for the solenoid, which typically connects to a switched 12-volt source through a fuse. Keep grounds clean and tight, since poor grounds are a common source of intermittent engagement.

Stage What to confirm
Carrier assembly Preload and backlash within manual specs
Air line No kinks, chafing or heat exposure
Solenoid wiring Fused feed, solid ground, correct polarity
Function test Locker engages and releases on command

Test Before Going on the Trail

Once the cover is back on and the fluid is filled to the level the manual specifies, raise the vehicle safely on stands and cycle the locker several times. Listen for a clean engagement and watch both wheels to confirm they turn together when locked. Check for leaks at every fitting. Then road-test in a low-speed, controlled area before any serious trail use. If the locker does not engage, the troubleshooting section of the manual and a qualified shop are good next steps.

  • Torque wrench set: Accurate torque is essential for carrier caps and cover bolts, and manuals specify exact values. View on Amazon
  • Dial indicator with magnetic base: Needed to measure ring gear backlash to the manual’s window. View on Amazon
  • Marking compound for gear contact: Lets you check tooth contact pattern before final assembly. View on Amazon

Common Mistakes

  • Skipping the manual’s preload and backlash steps and relying on memory.
  • Routing the air line too close to exhaust or suspension links.
  • Using a weak or unfused power feed for the solenoid.
  • Forgetting to refill the differential to the correct fluid level.
  • Not cycling the locker on stands before the first trail run.

For background on how the locker works before you begin, see What Is an ARB Air Locker? How It Works and When to Use One, and if you are buying a secondhand unit, Used ARB Air Locker: How to Buy, Inspect and Install One Safely (2026) covers what to check first.

FAQ

Do I need the exact manual for my axle?

Yes. Torque values, preload and backlash specifications differ between housings, so use the manual matching your axle and locker model.

Can I install an ARB air locker without removing the carrier?

Generally no. The locker mounts inside the carrier, so the differential must be opened. Confirm the removal steps in your manual.

What if the locker does not engage after installation?

Check the air supply pressure, solenoid wiring and ground first, then consult the troubleshooting section of the manual. If the problem persists, consult a qualified drivetrain technician.

Conclusion

A careful read of your arb air locker installation manual, followed by methodical carrier setup, clean air routing and a thorough function test, is what makes an install hold up on the trail. Work in the order the manual gives, verify every specification, and do not skip the bench test. When in doubt about any step, a qualified drivetrain shop can confirm the work.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our off-road vehicle upgrades guides, checking product details against manufacturer specifications and owner feedback.

About the author

Graham Fisher
Graham Fisher

Graham Fisher writes reviews and buying guides for Offroad Lockers.