We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Air Locker Denailer Gun: What It Is, How to Use One, and Common Mistakes

Learn what an air locker denailer gun is, how it fits into ARB-style air locker setups, and the steps and mistakes to know before you use one.

Updated November 2026

An air locker denailer gun is a specialty tool used during air locker work to hold, seat, or remove the small retaining components that keep the locker’s internal parts in place. This guide explains what the tool does, when it comes into play, and how to approach it safely. It also covers the common mistakes that cause trouble for people working on air locker differentials. Because the term “denailer gun” is not a standard, widely documented tool name in air locker service manuals, this article focuses on the function and safe handling of the tool category rather than promising a specific part number or model.

What an Air Locker Denailer Gun Is Used For

In most air locker service discussions, the work centers on the locker’s actuator, piston, spring, and the shift components that engage the spider gears. Retaining hardware, pins, and clips are often secured in ways that make them difficult to manipulate by hand. A tool in this category is generally used to grip, guide, or seat small fasteners and retainers without marring the housing or losing small parts into the differential case.

Shopping for one? See our guide: ARB Air Locker Differential Review (2026).

Before you buy or borrow any tool with this name, confirm exactly what your locker manufacturer’s service documentation calls for. Some tools marketed under similar names are really just pin punches, retaining clip tools, or snap-ring pliers with a different label. Matching the tool to the actual fastener type matters more than the name on the box.

When You Actually Need One

You are unlikely to need specialty retainer tooling for routine maintenance. It becomes relevant during:

  • Removing or reinstalling the air locker internals after a rebuild
  • Replacing a worn or damaged retaining clip or pin
  • Servicing a locker after contamination or a failed engagement
  • Installing an air locker kit into a differential that requires new retainers

If you are seeing engagement problems, check the basics first. Our guide to Why Is My ARB Air Locker Not Engaging? Causes and Fixes walks through the most frequent causes, and many of them have nothing to do with retaining hardware at all.

Tools and Supplies to Have on Hand

Whatever the exact tool name, work on an air locker differential will go more smoothly with a complete setup. Gather these before you open the housing:

  1. Clean work surface with a magnetic tray or labeled containers for every fastener
  2. The correct service manual or the locker manufacturer’s installation instructions for your axle
  3. Your retainer tool, pin punch set, or snap-ring pliers matched to the hardware
  4. Torque wrench with the specifications listed for your axle and locker model
  5. Thread locker or retainer compound if the manufacturer calls for it
  6. Clean shop rags, brake cleaner, and fresh gear oil at the correct fill specification

Step-by-Step: Working with Retainers Safely

Step 1: Document the Assembly

Photograph the internals before you remove anything. Note the orientation of every clip, pin, and spring. Retainers often go back in one way only, and reversing a clip can cause it to walk out under load.

Step 2: Relieve Tension

Springs and preloaded components can release suddenly. Keep your hands and face clear of the line of travel, and use the tool’s guide surfaces rather than prying with a screwdriver.

Step 3: Remove Retainers Without Damage

Seat the tool squarely on the retainer. Apply steady pressure rather than sharp force. If a retainer resists, stop and confirm you have the right tool size before you apply more force. Stripped or bent retainers are a common cause of later problems.

Step 4: Inspect the Seats and Bores

Look for burrs, scoring, or elongated holes. Light burrs can be cleaned with a fine file or stone. Anything deeper means the housing or component needs attention before reassembly.

Step 5: Reinstall to Specification

Seat each retainer fully and confirm it sits flush or within the tolerance your documentation describes. Use the specified thread locker only where the manufacturer calls for it. Check that the mechanism moves freely by hand before you close the housing.

Step 6: Verify Before Closing Up

Cycle the locker by hand or through the test sequence in your documentation. Confirm the actuator motion and internal travel match the expected pattern. Then install the cover, torque the fasteners to spec, and refill with the correct gear oil.

Common Mistakes

  • Using the wrong tool size: A slightly undersized tool can deform a retainer and make it impossible to seat cleanly.
  • Skipping photos or notes: Reassembly errors are far easier to avoid with a visual record.
  • Losing small parts: Work over a tray, not the open differential, and keep fasteners separated by type.
  • Overtightening retainers: Excess torque can crack housings and distort seats. Follow the spec.
  • Ignoring contamination: Metal flakes left behind will travel through the gears and cause wear.
  • Assuming all lockers are identical: Retainer design differs between manufacturers and axle generations.

Tips for a Cleaner Job

A matched pin punch set and a quality snap-ring plier set cover most retainer work better than any single specialty tool. A calibrated torque wrench is essential for correct retainer and cover torque. A magnetic parts tray keeps small clips from disappearing into the case.

  • Pin punch set: Helps drive and seat pins without marring the housing. View on Amazon
  • Snap-ring pliers set: Useful for internal and external retaining rings in many differential builds. View on Amazon
  • Click-type torque wrench: Lets you hit manufacturer torque values on covers and retainers. View on Amazon
  • Magnetic parts tray: Keeps fasteners sorted and prevents loss during teardown. View on Amazon

FAQ

Is an air locker denailer gun a standard tool?

Not in the sense of a universally named, standardized tool. The term is used informally. Confirm the exact retainer type and tool requirement in your locker manufacturer’s documentation.

Can I remove air locker retainers without a specialty tool?

Sometimes, but improvised methods often damage seats or retainers. Matching the correct punch or pliers to the hardware is the safer approach.

Do I need to replace retainers during a rebuild?

Many builders replace them as a precaution, especially if they show bending, flattening, or corrosion. Follow your manufacturer’s guidance.

What causes retainers to come loose?

Vibration, incorrect seating, overheating, and missing thread locker where it is specified can all contribute. Proper installation prevents most of these.

Should I use thread locker on every retainer?

No. Use it only where the manufacturer calls for it, since some fasteners are designed to be installed dry.

How do I know if a retainer is damaged?

Look for bends, flattened edges, cracks, or discoloration from heat. Any visible deformation is a reason to replace the part.

Is working on an air locker a job for a beginner?

Basic differential work is manageable with patience and the right manual, but internal locker work involves preloaded components. If you are unsure, consult a qualified driveline technician.

Where should I start if my locker is not engaging?

Begin with air supply, actuator function, and wiring before opening the differential. Diagnosis first avoids unnecessary teardown.

Conclusion

An air locker denailer gun, or the retainer tool it describes, is most useful when you know exactly which fastener you are working with. Document the assembly, use correctly matched tools, and verify function before closing the housing. Careful retainer work prevents most of the problems that send builders back into the differential. When in doubt, follow your manufacturer’s documentation or consult a professional driveline shop.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our off-road vehicle upgrades guides, checking product details against manufacturer specifications and owner feedback.

About the author

Graham Fisher
Graham Fisher

Graham Fisher writes reviews and buying guides for Offroad Lockers.