Air Locker Ap700 Review: Specs, Fit and Trail Performance Explained
Read this air locker AP700 review covering how the unit works, what to check before buying, installation considerations and trail-use tips for your build.
Updated November 2026
This air locker AP700 review explains what the AP700 is, how it engages, and what to verify before you put one in a driveshaft-to-axle setup. By the end, you will know whether this type of air locker fits your rig, what to inspect on a used unit, and how to avoid the common setup problems owners run into.
What the AP700 Is and How It Works
An air locker replaces the open or limited-slip action of a differential with a pneumatic clutch. When air pressure is applied, internal pistons push a locking collar that ties the two axle shafts together so both wheels turn at the same speed. When air is released, the spider gears return the differential to normal open operation. For background on the mechanics, see How Does Air Locker Work: Step-by-Step Guide to Operation and Setup and What Is an ARB Air Locker? How It Works and When to Use One.
Shopping for one? See our guide: ARB Air Locker Differential Review (2026).
Because the lock is all-or-nothing, the rig stops pulling in a straight line on pavement once engaged. That is why most builders run it only off-road and disengage it before highway speeds.
Check Fitment Before You Buy
Fitment is the first gate. Confirm the carrier model, ring-gear count, axle flange and pinion yoke spline against your axle. Owners often find that the mounting pattern works on one generation of axle and not another, so match the part number to your exact housing rather than the vehicle model alone. Comparing alternatives can help you confirm fit, such as TJM Pro Locker vs ARB Air Locker: Which Should You Choose? and Ox Locker vs ARB Air Locker: Which Should You Choose?.
Plan Your Air Supply and Controls
The locker needs a reliable air source, a solenoid, a switch and airline routed away from heat and sharp edges. Manufacturers generally specify a compressor sized for the locker’s fill volume and a regulated pressure within the range printed in the installation guide. Run a dedicated in-cab switch with an indicator light so you know the state of the locker at a glance.
- Mount the compressor and air tank on a solid, shielded location.
- Route airline along the frame or axle tube with clamps every 12 to 18 inches.
- Install the solenoid close to the locker to shorten the pneumatic run.
- Wire the switch through a fused circuit sized to the compressor.
- Test for leaks with soapy water at every fitting before driving.
Test and Tune After Installation
Bench-test the engage and disengage cycle with the vehicle lifted and wheels free. Listen for a clean click and confirm both wheels turn together when locked. Then road-test in a low-traction area at low speed. If engagement is sluggish, check the airline for kinks and confirm the compressor is building pressure. For troubleshooting, see Why Is My ARB Air Locker Not Engaging? Causes and Fixes.
Tools and Supplies Checklist
- Torque wrench and correct socket set for the carrier and cover bolts
- Gear oil matched to the axle manufacturer’s specification
- Pressure gauge and soapy water for leak checks
- Airline, push-to-connect fittings and cable clamps
- Fused wiring and a switch rated for the compressor load
Common Mistakes
- Buying a used unit without inspecting the piston seals and spider gears for wear.
- Skipping the gear oil fill or using the wrong viscosity, which shortens gear life.
- Running airline across the exhaust or against sharp frame edges.
- Leaving the locker engaged on pavement, which stresses drivetrain components.
- Undersizing the compressor so the locker engages slowly or not at all.
Recommended Gear
A quality inline air filter and water separator keeps moisture out of the solenoid and locker body, which is a frequent source of sticking. View on Amazon
A digital tire inflator with a built-in gauge is handy for checking air system pressure during setup and troubleshooting. View on Amazon
Heat-resistant wire loom protects the airline where it passes near hot components and moving suspension parts. View on Amazon
FAQ
Is the AP700 suitable for daily driving?
Not in the locked position. Air lockers should be disengaged on pavement, so most owners use them as a trail-only upgrade paired with an open or limited-slip setup for daily use.
How do I know if a used locker is worth installing?
Inspect the housing for cracks, check the piston and seal condition, and confirm the spider gears show no heavy pitting. If you are unsure, have a drivetrain specialist review it before you commit to installation. A related read: Air Locker AP700 Nail Remover Review: Key Features Explained.
Do I need a special compressor for an air locker?
You need one sized for the locker’s fill volume and the pressure your installation guide specifies. Undersized compressors cause slow or incomplete engagement.
Conclusion
The AP700 is a capable air locker when fitment, air supply and installation are handled carefully. Verify the part number against your axle, plan the airline and wiring before you start, and test thoroughly on a lift and on the trail. Gear work involves real safety risk, so consult a qualified drivetrain professional if you are unsure about any step.
Related reading
Ready to choose one?
