We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

ARB Air Locker Installation Instructions: A Step-by-Step Guide

Follow these arb air locker installation instructions to mount the carrier, run air lines, wire the solenoid and test engagement before your first trail run.

Updated November 2026

This guide walks you through the core arb air locker installation instructions in the order most installers use: prepare the axle, mount the locker and carrier, route the air line, wire the solenoid and verify engagement. By the end, you will have a locker that engages on command, holds air pressure and is ready for a proper shakedown test. Read the ARB fitment sheet for your exact axle before you start, because gear ratio, carrier model and cover design vary.

Prepare the Axle and Gather Tools

Drain the differential fluid and remove the cover, then pull the axle shafts and carrier. Clean the mating surfaces thoroughly, since any grit left behind can cause a leak or a binding carrier. Check the ring gear bolts and pinion for wear before you commit to the install, because this is the easiest time to address a problem.

Shopping for one? See our guide: ARB Air Locker Differential Review (2026).

  • Torque wrench and a full socket set
  • Dial indicator or magnetic base for backlash and pinion checks
  • Gasket sealant suitable for differential covers
  • Fresh gear oil at the specified capacity
  • Air line fittings, compressor-side connections and a pressure gauge
  • Multimeter for checking solenoid resistance and voltage

Mount the Locker and Set Carrier Preload

Install the air locker into the carrier, seat the bearing caps, and set preload and ring gear backlash to the figures in the manufacturer’s service manual. Too much preload accelerates bearing wear, while too little causes noise and rapid gear damage. Tighten the bearing cap bolts to the torque specified for your axle, then rotate the carrier by hand and confirm it turns smoothly without binding.

Reinstall the carrier, check the pinion depth, and confirm the tooth contact pattern on the ring gear before you fully torque everything down. A poor contact pattern is far easier to correct now than after the cover is sealed.

Run the Air Line and Wire the Solenoid

Route the air line along the axle tube and secure it with clamps, keeping it clear of the driveshaft, brake lines and exhaust. Avoid sharp bends and leave slack at the axle movement points. Mount the solenoid in a dry location, connect the power and ground, and run the wiring through a fused circuit to protect the system from shorts.

Sub-steps for Wiring

  1. Confirm the solenoid coil resistance matches the value listed in ARB’s documentation.
  2. Connect the positive lead through the recommended fuse.
  3. Ground the solenoid to bare metal on the chassis.
  4. Route the switch wiring into the cab and label each connection.

Seal, Fill and Test Engagement

Install the cover with a fresh gasket or sealant bead, refill with the specified gear oil, and check the level. Connect the air supply and apply pressure, then listen for the locker to engage. Test it on a level surface first, lifting one wheel if needed, and confirm both wheels drive together when the locker is on and separate normally when it is off.

Check every fitting for leaks with a soapy water solution. Bubbles indicate a leak that needs to be tightened or resealed. Make a short test drive at low speed and listen for unusual noise before taking the vehicle on a demanding trail.

Common Mistakes

  • Skipping the backlash and contact pattern check, which leads to early gear wear.
  • Routing the air line against hot exhaust or sharp suspension edges.
  • Using an unfused power feed or a poor ground connection.
  • Overtightening the cover bolts and distorting the gasket surface.
  • Testing the locker only in the driveway and assuming it will hold under load.

A quality torque wrench is essential for the bearing caps and cover bolts, since many failures trace back to incorrect torque. View on Amazon

A magnetic dial indicator base makes accurate backlash measurement far easier than estimating by feel. View on Amazon

FAQ

Do I need to remove the axle shafts to install an ARB air locker?

In most installs, yes, because the carrier must come out to fit the locker. Removing the shafts also makes it easier to inspect the bearings and seals.

How do I know if the locker is engaged?

With the vehicle lifted or on a low-traction surface, you should feel both wheels turn together when the locker is applied. Some owners also watch for a change in steering feel on a slippery surface.

Should I have a professional install my ARB air locker?

If you are not comfortable setting carrier preload and checking gear contact, consult a qualified drivetrain shop. Incorrect preload can cause serious and costly damage.

Conclusion

Careful preparation, correct preload and a clean air and wiring installation are the foundation of a reliable locker. Follow the manufacturer’s torque specifications and test thoroughly before you head onto the trail. A methodical install now saves time and repairs later.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our off-road vehicle upgrades guides, checking product details against manufacturer specifications and owner feedback.

About the author

Graham Fisher
Graham Fisher

Graham Fisher writes reviews and buying guides for Offroad Lockers.