Amber White LED Light Bar: How to Choose, Mount and Wire One
Learn how an amber white LED light bar works, how to pick the right one for your rig, and how to mount and wire it safely for trail and farm use.
Updated November 2026
An amber white LED light bar lets you switch between a bright white beam for distance and a warm amber beam for fog, dust and snow. This guide walks through choosing the right amber white LED light bar for your vehicle, mounting it securely and wiring it so it works with your ignition and switch setup.
Understand How Dual-Color Light Bars Work
Most amber white LED light bars use two separate LED circuits behind one lens. The white side produces a cool, high-output beam that reaches far down the trail. The amber side produces a longer-wavelength light that cuts through fog, road spray and airborne dust with less glare reflecting back at you.
Shopping for one? See our guide: Top 7 Light Truck Tires All Terrains for Trucks and SUVs in 2026.
Check whether the bar uses a single switch for both colors, a three-position switch, or a separate wire for each color. A three-position setup lets you run white only, amber only, or both together, and that flexibility is the main reason people choose a dual-color unit.
Choose the Right Size and Beam Pattern
Measure the width of your bumper, roof rack or grille before you buy. Most owners mount a bar that is 20 to 30 inches long on a bumper and 40 inches or longer on a roof rack, but check the mounting points on your vehicle first.
Pick the beam pattern based on how you drive. A spot pattern throws light far down the trail, while a flood or combo pattern spreads light wider for close-range work. Many dual-color bars use a combo pattern, which suits mixed trail and highway use.
Mount and Wire the Light Bar Safely
- Confirm the mounting bracket fits your vehicle and that the bar sits clear of the hood, grille and any sensors.
- Attach the bar to the bracket and tighten hardware to the torque the manufacturer specifies, then add thread-locking compound where the instructions call for it.
- Route the harness away from moving parts and sharp edges, using grommets wherever the wire passes through sheet metal.
- Fuse the positive lead within about 12 inches of the battery, using the fuse rating listed in the instructions.
- Connect the white and amber wires to the switch, then test each color separately before final mounting.
Set Up Switching and Power Control
Wire the bar through a relay rather than running it straight from the switch. The relay handles the current draw and protects your switch panel. If you want the light bar to work only with the engine running, tie the relay to an ignition-switched source. Otherwise you can run it from a key-off source and risk draining the battery.
| Wiring Method | Best For |
|---|---|
| Direct to switch | Low-current bars with a small load |
| Relay with inline fuse | Most dual-color bars and higher-output setups |
| Ignition-switched relay | Keeping the battery safe when parked |
Common Mistakes to Avoid
- Skipping the relay, which can overload the switch and cause heat damage.
- Mounting the bar where it blocks airflow to the radiator or interferes with a windshield-mounted camera.
- Using the wrong gauge wire for the run length, which causes voltage drop and dim output.
- Aiming the bar too high, which blinds oncoming drivers and can be illegal in some areas.
- Leaving the bar on with the engine off for long periods, which can drain the battery.
Recommended Gear
- Relay and inline fuse kit: A proper relay keeps the switch cool and protects the bar from voltage spikes. View on Amazon
- Mounting bracket set: Matching brackets make it easier to place the bar at the right height and angle. View on Amazon
- Heavy-gauge wiring harness: Proper wire gauge reduces voltage drop on longer runs. View on Amazon
If you plan to add a winch alongside your lighting, our guide to Light Duty Winch Electric: How to Choose, Mount and Use One (2026) covers the same kind of wiring and relay considerations.
FAQ
Can I run the amber and white LEDs at the same time?
Yes, most dual-color bars allow both colors together if the switch and wiring are set up for it. Check the instructions to confirm the combined current draw is within your switch and fuse ratings.
Do I need a relay for an amber white LED light bar?
A relay is strongly recommended because it protects the switch and keeps current away from your dash wiring. Consult a qualified automotive electrician if you are unsure about your vehicle’s electrical system.
Is amber light legal on the road?
Rules on auxiliary lighting vary by state and by whether the vehicle is on public roads or private trails. Check your state’s vehicle lighting regulations before using either color on public roads.
Conclusion
A dual-color amber white LED light bar gives you flexible lighting for trail, fog and farm work when it is sized, mounted and wired correctly. Plan the mounting position, add a relay and fuse, and test each color before the first trip. Take your time with the wiring and the light bar will serve you well for years.
Related reading
- Light Duty Electric Winch 120V: How to Choose, Mount and Use One
- Foot Locker White Air Force 1 Womens: Buying Guide and Sizing Tips
Ready to choose one?
